Replacing Rear Shocks
Moderators: Doone, westonwarrior
Replacing Rear Shocks
Hi All,
One of my rear shocks was leaking, so I've bought a new pair. As there are only a couple of bolts I figured I could DIY. Simple question : I don't own a spring compressor - is it required for the job or can the shock be bolted on without compressing the spring??
Any other tips gratefully received before I attack the van with a spanner!
Rob
One of my rear shocks was leaking, so I've bought a new pair. As there are only a couple of bolts I figured I could DIY. Simple question : I don't own a spring compressor - is it required for the job or can the shock be bolted on without compressing the spring??
Any other tips gratefully received before I attack the van with a spanner!
Rob
Re: Replacing Rear Shocks
Just put axle stands under the axle and let the weight of the body compress the springs.
I've only ever used compressors for front springs on struts.
I've only ever used compressors for front springs on struts.
Re: Replacing Rear Shocks
not needed just 2 bolts each
Re: Replacing Rear Shocks
Thanks guys 
I've got a trolley jack and the scissors jack, so between them both should get the alignment right!
Just hope the bolts come off ok

I've got a trolley jack and the scissors jack, so between them both should get the alignment right!
Just hope the bolts come off ok

- mikeonb4c
- Supreme Being
- Posts: 22877
- Joined: Sun Nov 05, 2006 10:49 pm
- Location: Living with Mango Bongo in the North West but with a tendency to roam
- Contact:
Re: Replacing Rear Shocks
Don't work underneath it without axle stands would be my advice. I've seen a 2 ton trolley jack let go when used on a Bongo, and a scissor jack (if used on the jacking points) won't keep the spring in compression.Rob101 wrote:Thanks guys
I've got a trolley jack and the scissors jack, so between them both should get the alignment right!
Just hope the bolts come off ok
Re: Replacing Rear Shocks
Mike's point can't be made to strongly.
Axle stands before you go under.
And on solid ground.
Axle stands before you go under.

And on solid ground.
Re: Replacing Rear Shocks
..... repeated for the avoidance of doubt.scanner wrote:Just put axle stands under the axle and let the weight of the body compress the springs.
I've only ever used compressors for front springs on struts.
- Simon Jones
- Supreme Being
- Posts: 9341
- Joined: Mon Aug 29, 2005 3:34 pm
- Location: Salisbury (ish), Wiltshire
Re: Replacing Rear Shocks
As said, spring compressors not required as the shocks are outside of the springs. I changed mine a while back and it's quite a simple job but you may find getting the lower bolts undone tricky if they've rusted. Lift the rear of the van and prop securely on stands so the axle is hanging and then use a trolley jack to just allow you to jiggle it around to take the weight off the bolt to allow it to be slid out.


Re: Replacing Rear Shocks
Thanks All - just letting you know I'm alive!
The nuts wouldn't budge, even with copious amounts of WD 40, so off to the mechanic we go!
(he's got a pit).
Rob
The nuts wouldn't budge, even with copious amounts of WD 40, so off to the mechanic we go!
(he's got a pit).
Rob
- mikeonb4c
- Supreme Being
- Posts: 22877
- Joined: Sun Nov 05, 2006 10:49 pm
- Location: Living with Mango Bongo in the North West but with a tendency to roam
- Contact:
Re: Replacing Rear Shocks
An all too common frustration to the best laid plans of mice and men, especially on an old BongoRob101 wrote:Thanks All - just letting you know I'm alive!
The nuts wouldn't budge, even with copious amounts of WD 40, so off to the mechanic we go!
(he's got a pit).
Rob
