Glow Plugs
Posted: Tue Nov 17, 2020 9:08 pm
I can see that the glow plugs has been covered many times & there is a lot of info including a fact sheet, however...
Checking the fact sheet & my VIN number it recommended that I needed the short glow plugs for my 98’ Bongo so I ordered a set of NGK 5116 Y-701J
These were the short (83mm) plugs needed going by the factsheet.
When I removed my old plugs they were the long (103mm)
My current plugs have been in for around 3-years & still going strong (reading around 1.1 - 1.6 Ohms) I just wanted to change them as it’s been nearly 3-years & carrying out a full service.
The plugs removed are;
ND 067100-1850
142000-1850
I would buy these again no problem given that they haven’t failed in the 3-years after hearing some have had to change annually, but can’t seem to find them anywhere?
I have read that the BluePrint ADK81801 plugs do not seem to last, & haven’t heard much about the NipParts J5718000.
I have contacted NGK as would rather pay more & fit a quality (known brand) plug but they do not make a plug for the long (103mm) Bongo’s only the short ones mentioned above.
I have contacted MazdaBongo who can supply Techno plugs (which he said come with 12-month warranty & have never had any complaints) at a reasonable price but never heard of this make & after a google search there is very little info so asked if there was any other makes.
He managed to source a set of HKT plugs from Japan which would certainly be more suitable & hopefully longer lasting being Japan for a Jap motor, but again not much info found on these either & the delivery time could be an issue as I have my old plugs out ready for the new ones, So...
Thought I would ask everyone & see what others have fitted/recommend & if theirs any known brand that can be sourced for the long (103mm) Bongo’s?
Due to not being able to find any known brands I have thought about fitting the shorter (83mm) NGK Y-701J plugs but rather than modifying the fuel rail (bending it out of the way) I was thinking of using wither M4 20-25mm Standoffs (screwed onto the glow plugs) to extend the height for the bus bar or making up insulated link wires with ring terminals to connect to all the plugs, has anyone tried any of the above & had any success or issues?
By doing this would surely make things easier for future also as NGK is a top brand & very easy to get a hold of.
Any advice/info appreciated
Checking the fact sheet & my VIN number it recommended that I needed the short glow plugs for my 98’ Bongo so I ordered a set of NGK 5116 Y-701J
These were the short (83mm) plugs needed going by the factsheet.
When I removed my old plugs they were the long (103mm)
My current plugs have been in for around 3-years & still going strong (reading around 1.1 - 1.6 Ohms) I just wanted to change them as it’s been nearly 3-years & carrying out a full service.
The plugs removed are;
ND 067100-1850
142000-1850
I would buy these again no problem given that they haven’t failed in the 3-years after hearing some have had to change annually, but can’t seem to find them anywhere?
I have read that the BluePrint ADK81801 plugs do not seem to last, & haven’t heard much about the NipParts J5718000.
I have contacted NGK as would rather pay more & fit a quality (known brand) plug but they do not make a plug for the long (103mm) Bongo’s only the short ones mentioned above.
I have contacted MazdaBongo who can supply Techno plugs (which he said come with 12-month warranty & have never had any complaints) at a reasonable price but never heard of this make & after a google search there is very little info so asked if there was any other makes.
He managed to source a set of HKT plugs from Japan which would certainly be more suitable & hopefully longer lasting being Japan for a Jap motor, but again not much info found on these either & the delivery time could be an issue as I have my old plugs out ready for the new ones, So...
Thought I would ask everyone & see what others have fitted/recommend & if theirs any known brand that can be sourced for the long (103mm) Bongo’s?
Due to not being able to find any known brands I have thought about fitting the shorter (83mm) NGK Y-701J plugs but rather than modifying the fuel rail (bending it out of the way) I was thinking of using wither M4 20-25mm Standoffs (screwed onto the glow plugs) to extend the height for the bus bar or making up insulated link wires with ring terminals to connect to all the plugs, has anyone tried any of the above & had any success or issues?
By doing this would surely make things easier for future also as NGK is a top brand & very easy to get a hold of.
Any advice/info appreciated
