Fiamma F35 canopy question?
Moderator: Muzorewa
Fiamma F35 canopy question?
Hiya
Buying an F35 pro Fiamma roll out canopy and wondered if someone can confirm the correct Fiamma brackets required to fit the Bongo please?
Believe its the Fiamma VW T4 ones but want to be sure before ordering!
Thanks
Mark
Buying an F35 pro Fiamma roll out canopy and wondered if someone can confirm the correct Fiamma brackets required to fit the Bongo please?
Believe its the Fiamma VW T4 ones but want to be sure before ordering!
Thanks
Mark
-
- Apprentice Bongonaut
- Posts: 1
- Joined: Wed Jan 09, 2013 3:06 pm
Re: Fiamma F35 canopy question?
Hi
I think you need the fiamma VWT3/Mazda Bongo kit 2 pcs 8cm brackets part number 98655-035.
For models after 1980.
Regards
Steve
I think you need the fiamma VWT3/Mazda Bongo kit 2 pcs 8cm brackets part number 98655-035.
For models after 1980.
Regards
Steve
Re: Fiamma F35 canopy question?
Mmmm not sure Steve re the T3 version! Looking at photo's on the forum they look different to the T3 and more like the T4 version.cadman5641 wrote:Hi
I think you need the fiamma VWT3/Mazda Bongo kit 2 pcs 8cm brackets part number 98655-035.
For models after 1980.
Regards
Steve
Anyone else who has carried this conversion out answer my SOS please???
Re: Fiamma F35 canopy question?
According to this Ebay listing the T3 brackets will fit;
http://www.ebay.co.uk/itm/FIAMMA-AWNING ... 5899e9319c
http://www.ebay.co.uk/itm/FIAMMA-AWNING ... 5899e9319c
Re: Fiamma F35 canopy question?
Thanks for the pointers both, looks like its the T3 version I need then.
Found it £30 cheaper too so happy days.
Found it £30 cheaper too so happy days.
Re: Fiamma F35 canopy question?
Hi, The T3 will fit but it is a tight fit. At the back you will need to manipulate the gutter a little and at the front, careful placement in between the doors is required...but is possible because I have done it! I also recommend a thick sticky pad under each bracket as this prevents rocking on the gutter. Someone makes proper brackets though...but I can't remember who? Dave
Re: Fiamma F35 canopy question?
I've put a stainless bolt through the brackets which prevents any rocking on the gutter and stops it bending.
The awning's rock solid and it helps to stop it rattling.
It obviously means drilling holes in the bodywork but as we have no intention of removing the awning it's not a problem.
The awning's rock solid and it helps to stop it rattling.
It obviously means drilling holes in the bodywork but as we have no intention of removing the awning it's not a problem.
Re: Fiamma F35 canopy question?
Shall be fitting this weekend hopefully, thanks for the info.
Re: Fiamma F35 canopy question?
Unfortunately, Fiamma never designed a bracket to fit the Bongo but over the years the T3/T4 Bracket was adapted by converters and with some gently persuasion fitted reasonably well, however the gauge of the bracket (quarter plate steel) is in my opinion a 'sledge hammer to crack a nut' especially when it is used to support the light weight f35 Pro... I made my brackets up from 3.0mm S/S bolted on to the roof panel which support's my F45S..don't rust, much lighter that the T3/T4 onesGixermark wrote:Hiya
Buying an F35 pro Fiamma roll out canopy and wondered if someone can confirm the correct Fiamma brackets required to fit the Bongo please?
Believe its the Fiamma VW T4 ones but want to be sure before ordering!
Thanks
Mark
Re: Fiamma F35 canopy question?
now if you got a Atf bongo an if the 35por fitting the same as the 45s then i would ring these BRIGEWATER METALCAFT LTD there made one that fits on the d ring blots an means you can get 3 fittings an not 2 wait hangs from the blots not the gutter.
i just had a look it dosnt seem the same fitting on the top .
i just had a look it dosnt seem the same fitting on the top .
take it easy drive a bongo
Re: Fiamma F35 canopy question?
take a look at this http://igmaynard.co.uk/bongo/forum/view ... 47&t=59535 looks like you could use the same brakets as us
take it easy drive a bongo