Search found 22 matches
- Tue Mar 05, 2013 1:24 am
- Forum: Techie Stuff
- Topic: Injector pump replace or repair
- Replies: 17
- Views: 5524
Re: Injector pump replace or repair
Thanks for the info. It's not a cold start start problem (checked all of that a couple of years ago from advice on forum) It's a cold running problem, after 2 years and many garages this garage confirmed what a lot of people said on here, 99% sure it's seals in the injector pump gone hard, this mean...
- Mon Mar 04, 2013 1:35 am
- Forum: Techie Stuff
- Topic: Injector pump replace or repair
- Replies: 17
- Views: 5524
Injector pump replace or repair
Hello All from New Zealand. I'm looking for some advice on the Injector pump issue that i've had for a very long time now. I've a 2.5 TD AFT Bongo. Over the last couple of years I've had a cold running issue which has been said is the 'Seals of the Injector pump hardening' for the last 4 months i've...
- Sun May 27, 2012 7:44 am
- Forum: Techie Stuff
- Topic: Would a Petrol fit instead of Diesel?
- Replies: 22
- Views: 4249
Would a Petrol fit instead of Diesel?
My 1996 AFT with a Diesel 2.5 WLT engine now needs some major work.
So i'm thinking a new engine, but, would a petrol engine fit rather than the WLT?
Thanks
Andy
Kerikeri NZ.
So i'm thinking a new engine, but, would a petrol engine fit rather than the WLT?
Thanks
Andy
Kerikeri NZ.
- Thu Mar 08, 2012 6:03 pm
- Forum: Techie Stuff
- Topic: Cold starting issue (yet again, sorry)
- Replies: 9
- Views: 3097
Re: Cold starting issue (yet again, sorry)
The heart of the problem is the fact that it keeps cutting out when started from cold. I notice there were a couple of others on here with the same issue, and the main reason for this thread was to see if they had solved the issue. For me, this has been going on for 2 years, and i've been to 4 garag...
- Thu Mar 08, 2012 1:50 am
- Forum: Techie Stuff
- Topic: Cold starting issue (yet again, sorry)
- Replies: 9
- Views: 3097
Re: Cold starting issue (yet again, sorry)
At Ady Solenoids seem to work ok, when starting seems to rev' in the region of 900 - 925. No vbration upon starting normally. Gasket fails in the same way, blowing outwards, not had any sucking in up to now. I'll try that with the rear box, as soon as the rain stops. I had a new rear box put on 14 m...
- Wed Mar 07, 2012 12:59 am
- Forum: Techie Stuff
- Topic: Cold starting issue (yet again, sorry)
- Replies: 9
- Views: 3097
Cold starting issue (yet again, sorry)
I’ve now had this issue for a couple of years and I notice by doing a search that others have also had this same problem (including my post 18 months ago), so here’s the thing Did anyone actually solve the problem on here? Here’s a brief list of stuff that I’ve done or had done, but should mention t...
- Fri Oct 22, 2010 12:57 am
- Forum: Techie Stuff
- Topic: Engine cut out
- Replies: 27
- Views: 8118
Re: Engine cut out
@ Northern Bongolow, sent you a PM. Hope you get it, for some reason it seems not to be in my sent box yet, just sat in my out box waiting to go?
Andy
Andy
- Thu Oct 21, 2010 2:18 am
- Forum: Techie Stuff
- Topic: Engine cut out
- Replies: 27
- Views: 8118
Re: Engine cut out
[quote="Northern Bongolow"]hi sorry for the delay in replying to your pics.
quote]
Thank you, please don't feel you have to say sorry, I'm just really grateful for the advice.
I'll take a look at the set-up, adjust as I can and see how it goes.
THANK YOU again.
Andy
quote]
Thank you, please don't feel you have to say sorry, I'm just really grateful for the advice.
I'll take a look at the set-up, adjust as I can and see how it goes.
THANK YOU again.
Andy
- Wed Oct 20, 2010 1:18 am
- Forum: Techie Stuff
- Topic: Engine cut out
- Replies: 27
- Views: 8118
Re: Engine cut out
This Bl**dy van!!!!!!!!! It's been fine for a short while, and not it's being the worst it's ever been. It's started to just cut out now as I'm going along. It just loses power, I push on the throttle and nothing, just dead, it will then either cut right out and die so I have to start it again, or o...
- Sat Oct 02, 2010 3:55 am
- Forum: Techie Stuff
- Topic: Engine cut out
- Replies: 27
- Views: 8118
Re: Engine cut out
Hello again, I’ve now taken a picture of the choke plunger screw which engages the throttle cable plate. (Please excuse quality) The first pic’ is in the ‘Full on’ position http://i1237.photobucket.com/albums/ff480/ziggi-/Bongoinfullonposition.jpg The second pic’ is in the ‘Mid on’ position http://i...
- Thu Sep 30, 2010 4:22 am
- Forum: Techie Stuff
- Topic: Engine cut out
- Replies: 27
- Views: 8118
Re: Engine cut out
I’m still wondering if the plunger needs adjusting, as mentioned above, there seems to be a lot of thread on the back, and when it’s in the ‘warm / off’ position there’s 10mm gap between tread end and contact plate of throttle cable. dont really understand this coment,are you saying that the end of...
- Mon Sep 27, 2010 12:24 am
- Forum: Techie Stuff
- Topic: Engine cut out
- Replies: 27
- Views: 8118
Re: Engine cut out
Symptoms been on here many times........ I have always diagnosed Diesel Injector Pump and mostly been correct.... :wink: You could I guess start and try cleaning it and the injectors by running a new diesel filter full of injector cleaner......then if it still stalls like you say......I favour the ...
- Mon Sep 27, 2010 12:15 am
- Forum: Techie Stuff
- Topic: Engine cut out
- Replies: 27
- Views: 8118
Re: Engine cut out
Okay an update. Firstly, sorry I forgot to mention on the first posting that the fuel filter was replaced about 6 weeks ago. I’ve now changed both valve switches mentioned above (the right hand one finally blew on Sat’) and the plunger appears to be working I.E. it now engages prior to start, and re...
- Thu Sep 23, 2010 9:55 pm
- Forum: Techie Stuff
- Topic: Engine cut out
- Replies: 27
- Views: 8118
Re: Engine cut out
That is the one! Spoken to Mech' and he confirmed it was the right hand side. Could you advise on the setting for the plunger? My plunger seems to have so much thread remaining out the back that when it does engage it's 'only just' making contact, to the point where I'm not sure if it puts any press...
- Thu Sep 23, 2010 2:29 am
- Forum: Techie Stuff
- Topic: Engine cut out
- Replies: 27
- Views: 8118
Re: Engine cut out
Thanks for all the advice, I am working my way through it all and hope to get the garage to work with me to cure it. The Mech' who did the service advised me he found a 'split pipe and damaged switch/valve so he glued it for now' I've yet to pin him down to show me in detail what he did (heavy snow,...